•  
  • Sitemap

    • innomic.com

      • Industry Solutions

        Whether machine, building or human vibration. The right solution for your measurement task can be found here.

        • Machine Vibrations

          Ensure the quality of your machines by using vibration measurement equipment. Production processes can be optimized and wear can be reduced.

          • Products

          • Complete Solutions

            • Machine Diagnosis

              With the VibroMatrix® Kit for Machine Diagnosis you have a powerful system that helps you to diagnose and eliminate any problems caused by vibrations.

            • Balancing

              The VibroMatrix Kit provides you with everything you need for Single- or Two-Plane-Balancing.

            • Wind Energy Turbines

              You find everything you need to measure vibrations on wind energy turbines acc. VDI 3834:2008 in one handy case.

          • VibroMatrix®

          • Monitoring

          • Sensors

            These piezoelectric accelerometers are especially convenient to measure machine vibrations.

            • iCS80

              iCS80 features a double sealed and isulated case to avoid ground loop problems, double shielding for best EMI protection and a degree of protection of IP67.

            • KS81B

              KS81B offers a double sealed and insulated case avoiding ground loops, double shielding for best EMI protection and protection grade IP67.

            • KS813B

              The triaxial industry IEPE-accelerometer in a rugged stainless steel housing offers an insulated base avoiding ground loops and the protection grade IP67.

            • KS823B

              The accelerometer KS823B is especially usefule to measure vibrations in buildings and windenergy turbines.

            • AC915-1A

              AC915-1A is an intrinsically safe accelerometer with ATEX certificate zone 0 and axial output.

            • AC916-1A

              AC916-1A is an intrinsically safe accelerometer with ATEX certificate zone 0 and radial output.

            • KSI80VC-20

              KSI80VC-20 (measurement range 0.2 .. 25 mm/s, linear frequency range 1,5..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI80VC-40

              KSI80VC-40 (measurement range 0.4 .. 50 mm/s, linear frequency range 1,5..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI82VB-20

              KSI82VB-20 (measurement range 0.2 .. 25 mm/s, linear frequency range 10..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI82VB-40

              KSI82VB-20 (measurement range 0.5 .. 50 mm/s, linear frequency range 10..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

          • Services

        • Building Vibrations

        • Human Vibrations

      • Products

        The IDS Innomic GmbH offers precise vibration measurement equipment, beginning with vibration transducers through signal conditioners up to vibration meters.

        • Solution Overview

          In this overview you find the suitable vibration measurement systems including the related components for the respective measurement tasks.

        • VibroMatrix

          VibroMatrix converts PCs, netbooks and notebooks into vibration measurement equipment with real-time charts. The subsequent offline analysis in the office becomes a breeze too. VibroMatrix offers a ready to use software for vibration measurement.

          • Design

            The vibration measurement system VibroMatrix consists of hardware (USB adapter InnoBeamer) and software instruments.

          • VibroMatrix® Kits

            Some vibration measurement tasks occur repeatedly. In line with this, these meaurement kits provide you the essential components with a price advantage.

            • Machine Diagnosis

              With the VibroMatrix® Kit for Machine Diagnosis you have a powerful system that helps you to diagnose and eliminate any problems caused by vibrations.

            • Balancing

              The VibroMatrix Kit provides you with everything you need for Single- or Two-Plane-Balancing.

            • Building Vibration

            • Human Vibrations

            • Wind Energy Turbines

              You find everything you need to measure vibrations on wind energy turbines acc. VDI 3834:2008 in one handy case.

          • VibroMatrix® Modules

            • Instruments

              The software instruments operate on the screen of your PC in real-time. Numerous vibration measurands, characteristic values and units are supported.

            • InnoBeamer®

            • Event Annunciators

              Event Annunciators are used for transfering infomations via e-mail, signaling in an extra display and using radio switches.

            • InnoMaster®

              The InnoMaster® RT is the control center of VibroMatrix®. Here you configure the measurement chain and record the global settings.

          • Get to know VibroMatrix®

            You can test the digital vibration measurement system VibroMatrix® without commitment in different ways.

          • VibroMatrix® Documentation

          • Practice

            Here you find Application Reports, TechInfos, current builds and references on digital vibration measurement with VibroMatrix®.

            • Application Reports

              Start reading the application reports about VibroMatrix®, e.g. ensuring occupational safety for pressure washers, vibration measurement on wind energy turbines

            • TechInfos

            • References

              Below you will find a selection of customers who successfully use VibroMatrix to solve their vibration measurement tasks.

            • Version Builds

              Follow the development of VibroMatrix-Software and InnoBeamer. Find out everything about new features and solved errors.

          • Downloads

            On this page you find the downloads around our USB-vibration measuring system VibroMatrix.

          • Prices & Offers

            You can request price lists of VibroMatrix® and we inform you about the price advantages you can get by discounts, the clone function and the measurement kits.

          • FAQ

            We answer your questions about digital vibration measurement with VibroMatrix®.

        • Vibration Transducers

          These maintenance-free, piezoelectric vibration transducers for various purposes measure dynamic acceleration. With appropriate vibration measurement technique they may be used as well to measure vibration velocity and displacement (deflection).

          • All Sensors

            In this overview you will find all piezoelectric accelerometers of our product portfolio.

          • Industry

            Due to the rugged design these piezoelectric accelerometers are suitable for industrial applications of vibration measurement.

            • iCS80

              iCS80 features a double sealed and isulated case to avoid ground loop problems, double shielding for best EMI protection and a degree of protection of IP67.

            • KS81B

              KS81B offers a double sealed and insulated case avoiding ground loops, double shielding for best EMI protection and protection grade IP67.

            • KS74C.10

              KS74C.10 (sensitivity: 10 mV/g) with its rugged stainless steel housing features the protection grade IP64 and an insulated base to avoid ground loops.

            • KS74C.100

              KS74C.100 (sensitivity: 100 mV/g) with its rugged stainless steel housing features the protection grade IP64 and an insulated base to avoid ground loops.

            • AC915-1A

              AC915-1A is an intrinsically safe accelerometer with ATEX certificate zone 0 and axial output.

            • AC916-1A

              AC916-1A is an intrinsically safe accelerometer with ATEX certificate zone 0 and radial output.

            • KSI80VC-20

              KSI80VC-20 (measurement range 0.2 .. 25 mm/s, linear frequency range 1,5..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI80VC-40

              KSI80VC-40 (measurement range 0.4 .. 50 mm/s, linear frequency range 1,5..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI82VB-20

              KSI82VB-20 (measurement range 0.2 .. 25 mm/s, linear frequency range 10..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KSI82VB-40

              KSI82VB-20 (measurement range 0.5 .. 50 mm/s, linear frequency range 10..1000 Hz) displays RMS of vibration velocity as 4..20mA loop signal.

            • KST94C-4N

              KST94C-4N with its movable tip is suitable for automated measurements, for instance in quality control.

            • KST94C-9N

              KST94C-9N with its movable tip is suitable for automated measurements, for instance in quality control.

          • General Purpose

            General purpose accelerometers are especially convenient for most vibration measurement and analysis in many applications. Errors due to thermal transients are prevented by using the shear principle.

            • KS56

              KS56, a piezoelectric accelerometer with charge output, offers an operating temperature up to 250°C and an axial cable connector.

            • KS57

              KS57, a piezoelectric accelerometer with charge output, offers an operating temperature up to 250°C and a radial cable connector.

            • KS76C.10

              KS76C.10, a piezoelectric IEPE accelerometer with axial cable connector, offers a high linear band width up to 33kHz and a high resolution.

            • KS76C.100

              KS76C.100, a piezoelectric IEPE accelerometer with a sensitivity of 100mV/g and an axial cable connector, offers a high resolution nad low noise.

            • KS77C.10

              KS77C.10, a piezoelectric IEPE accelerometer with radial cable connector, offers a high linear band width up to 33kHz and high resolution.

            • KS77C.100

              KS77C.100, a piezoelectric IEPE accelerometer with radial cable connector, offers high resolution and low noise.

            • KS78.10

              IEPE accelerometer KS78.10 is a low-cost model and features an insulated housing and an contained electronic data sheet (TEDS).

            • KS78.100

              IEPE accelerometer KS78.100 is a low-cost model and features an insulated housing and an contained electronic data sheet (TEDS).

          • Miniature

            Miniature accelerometers are especially suitable for vibration measurement with light objects.

            • KS91B

              Since KS91B itself weighs only 1 gram it is especially suitable to measure vibrations on light objects.

            • KS93

              Miniature accelerometer KS93 with its charge output weighs only 2,7 gram and features a high resonant frequency and a wide dynamic range.

            • KS94B.10

              KS94B.10 (2,4 gram, axial cable connector) allows a high resolution even at low frequencies and features an internal resonant frequency compensation, linear up to 40 kHz.

            • KS94B.100

              KS94B.100 (3,2 gram, axial cable connector) allows a high resolution even at low frequencies and features an internal resonant frequency compensation, linear up to 40 kHz.

            • KS95B.10

              KS95B.10 (2,4 gram, radial cable connector) allows a high resolution even at low frequencies and features an internal resonant frequency compensation, linear up to 40 kHz.

            • KS95B.100

              KS95B.100 (3,2 gram, radial cable connector) allows a high resolution even at low frequencies and features an internal resonant frequency compensation, linear up to 40 kHz.

          • High-Sensitivity

            These vibration transducers are used for building examinations and seismic measurements. Because of their high sensitivities, slightest vibrations can be measured.

            • KB12VD

              KB12VD features an extremly high sensitivity of 10000mV/g which is especially suitable for seismic and buidling vibration measurement particularly at low frequencies.

            • KS48C

              high-sensitivity, seismic, piezoelectric, integrated amplifier, IEPE, vibration measurement

          • Shock

            Due to their low sensitivity, shock sensors are suitable for the measurement of high accelerations.

            • iQD62.005

              The shock accelerometer iQD62.005 in a rugged stainless steel housing offers an extremely low sensitivity of 0,05 mV/g.

            • iQD62.1

              The shock accelerometer iQD62.1 in a rugged stainless steel housing offers an extremely low sensitivity of 1 mV/g.

          • Triaxial

            The piezoelectric triaxial accelerometers serve for concurrent measurement in all three axes.

            • KS903.10

            • KS903.100

            • 3023A1T

            • 3023A9

            • 5313A

              5313A is a triaxial accelerometer embedded into a rubber pad intended for the measurement of human exposure to whole-body vibration acc. to ISO 2631.

            • KS813B

              The triaxial industry IEPE-accelerometer in a rugged stainless steel housing offers an insulated base avoiding ground loops and the protection grade IP67.

            • KS823B

              The accelerometer KS823B is especially usefule to measure vibrations in buildings and windenergy turbines.

            • KS943B.100

              Due to its weight of only 16 grams the triaxial IEPE-accelerometer with a sensitivity of 100mV/g is suitable for light test objects. It features a central drilling for easy mounting and axis alignment.

          • OEM

            OEM Accelerometers are convenient for integration into machines and instruments.

            • KS90

              KS90, an OEM Accelerometer in low-cost TO-39 transistor case with solder pins with charge output, offers a high resonant frequency and a wide dynamic range.

            • KS901.10

              KS901.10 features a rugged stainless steel housing (sensitivity: 100mV/g) which is convenient for integration into machines by adhesive or clamp mounting.

            • KS901.100

              KS901.100 features a rugged stainless steel housing (sensitivity: 100mV/g) which is convenient for integration into machines by adhesive or clamp mounting.

        • Measurement Microphones

        • Impact Hammer

        • Measurement Equipment

          IDS Innomic offer precise vibration measurement equipment: Measurement equipment for stationary and mobile machine monitoring, signal conditioners for the connection of piezoelectric sensors for example to an oscilloscope and calibrators.

          • Signal Conditioner

            Signal conditioners for measuring and industrial purposes transform signals of piezoelectric sensors into a handy voltage signal.

            • M72A1 and M72B1

              The charge amplifiers M72A1 and M72B1 with adjustable gain / filter frequency allow the direct measurement of vibration acceleration, speed and displacement.

            • M72A3 and M72B3

              The 3-channel charge amplifiers M72A3 and M72B3 with adjustable gain / filter frequency allow the direct measurement of vibration acceleration, speed and displacement.

            • M72S1 and M72R1

              Charge amplifiers M72S1 and M72R1 are suited for 19 inch rack mounting and therefore enable multi-channel measuring systems.

            • IEPE100

              Remote Charge Converter IEPE100 converts the charge signal of vibration transducers with charge output into a voltage signal.

            • M208A

              The 8-channel signal conditioner M208A is simultaneously an rms/peak meter and allows the vibration monitoring with relay output/remote monitoring via the internet.

            • M208B

              The 8-channel signal conditioner M208B is simultaneously an rms/peak meter and allows the vibration monitoring with relay output/remote monitoring via the internet.

            • M28

              The modular supply unit for accelerometers with an integrated amplifier can be used for signal conditioning in dynamic vibration measurement.

            • M32

              The sensor supply unit with adjustable gain 1/10/100 is used for signal conditioning for dynamic measurements.

          • Vibration Monitoring

            The presented devices (vibration monitor M12B, vibration switch VS6) allow a stationary monitoring of important facilities.

            • M12B

              The modular vibration monitor M12B serves to monitoring of vibration velocity and emergency shut-off or alarm tripping in case of increasing vibration levels.

            • M208A

              The 8-channel signal conditioner M208A is simultaneously an rms/peak meter and allows the vibration monitoring with relay output/remote monitoring via the internet.

            • VS10 and VS11

              The vibration switches VS10 and VS11 feature peak and RMS vibration monitoring with selectable frequency limits and include piezoelectric accelerometers.

          • Mobile Vibration Meters

            The mobile vibration meters VM22, VM 24 and VM25 are used for the mobile machine monitoring. The VM31 is a mobile vibration meter for the mobile human vibration measurement.

            • VM22, VM24 and VM25

              The pocket vibration meters of the VM2x series are able to record three measurands as well as temperature and speed.

            • VM31

              The mobile vibration meter vm31 can be used for the measurement of hand-arm and whole-body human vibrations acc. to ISO 5349 and ISO 2631.

          • Vibration Calibrators

            For calibration of vibration sensors and measuring chains, we offer calibrators with fixed frequency and a calibration system with variable frequency.

            • VC20 and VC21

              The vibration calibrators VC20 and VC21 are used as vibration exciters for examination/calibration of vibration sensors and measuring systems.

            • VC120

              The vibration calibrator with variable frequency (70..10 000 Hz) is designed for calibration as well as fault detection of vibration measuring systems and the determination of amplitude response.

        • Accessories

          With these accessories for sensor connection and mounting, sensors and equipment can be adjusted to different applications.

      • Service

      • Infothek

        Erfahren Sie mehr zur technischen Anwendung der Schwingungsmesstechnik Software VibroMatrix. Wir haben Ihnen ausführliche und relevante technische Details hier zusammengestellt.

        • Schwingungskennwerte messen

          Messen Sie Schwingungskennwerte, um Maschinenschwingungen richtig einzuschätzen oder Instandhaltungen bedarfsgerecht zu planen.

        • Frequenzanalyse

          Wir zeigen Ihnen, wie Sie mit VibroMatrix eine Frequenzanalyse durchführen, um charakeristische Bauteilschwingungen leicht zu identifizieren und zu bewerten.

        • Ordnungs- und Nachlaufanalyse

          Mit den Techniken der Ordnungs- und der Nachlaufanalyse können Sie insbesondere drehzahlabhängige Schwingungen von Maschinen detailliert untersuchen.

        • Auswuchten

          Erfahren Sie, wie Sie die Ursachen von Unwuchten erkennen und mithilfe der unterschiedlichen Schritte des Auswuchtens beseitigen.

        • Wälzlagerdiagnose

          Wälzlager trennen den rotierenden vom feststehenden Teil der Maschine und sind damit stark belastet. Im Praxisbeispiel zeigen wir, wie Sie Lagerschäden frühzeitig erkennen und den Lagerkomponenten zuordnen können.

        • Eigenfrequenzen

          Bestimmen Sie die Eigenfrequenzen von Bauteilen, um Schwingungs- und Geräuschemissionen zu verhindern.

      • About us